Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
We have encountered this post about A Step-by-Step Guide to Installing a Bathtub directly below on the web and reckoned it made good sense to write about it with you on this page.
Setting up a bath tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is easily easily accessible, the project can relocate speedily; if you need to open a wall surface to get rid of the old tub and also position the brand-new bath tub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the work as well as are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed project, it is better to think about utilizing one before you begin. Chances are you might need an expert plumber to make tube connections.
This article will certainly assist you install a brand-new bath tub in your shower room if you have currently gotten a new tub as well as don't require to alter the arrangement of your previous supply of water pipes.
Your devices as well as product list need to make up the following:
Preparing for the Setup
Firstly, the sustaining structure provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets system to stop strain on the bath tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you use every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, after that the first thing you must do is detach the water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Utilizing the two wooden boards under its feet, put the bath tub in the called for setting. The wooden boards are valuable in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the bath tub till the level reads level.
To install faucets, fit all-time low of the outermost flexible faucet adapter to the ideal supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the water and examine all joints and new pipework for leakages and also tighten them if required. Fill up the bath tub as well as also inspect the overflow electrical outlet and also the regular outlet for leaks.
Finally, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bath tub must wait up until the bathtub has been made use of a minimum of once as this will resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washing machines are in location in between the faucet and the sink. Protect the faucet in position with the supplier offered backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The former type should be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a rigid seal, causing the water to permeate the wall in between the bath as well as the tiling, resulting in issues with dampness and possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and fittings. They are offered in tubes and cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealant can fracture rather very early if you do not take into account this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is suggested to fit the floor tiles utilizing water-resistant or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our excerpt on Installing A Bathtub. Thank you so much for taking the time to browse our piece. Sharing is good. One never knows, you may just be helping someone out. Thanks so much for going through it.
Act immediately. Report this page